Harness with mooring tail

Izajes » Productos » Harness with mooring tail

As always, our Products are here to strengthen your Company.

Harness with mooring tail

Code A40

Izajes y Transmisiones S.A. has developed ENCAN®, a brand comprised of personal protection products to prevent falling from heights.

The new line of products offers harnesses, fall arrest equipment and positioning lines, sliding fall arrest devices, lifelines and different accessories to supplement and make system assembly less difficult.

ENCAN® offers a wide range of equipment for all activities and work conducted at heights.

All ENCAN® products strictly comply with the applicable IRAM standards. We have our own world class laboratory in our plant, including a fall/training tower.

Since we know the market and the companies’ needs, we understand that our customers require excellent product quality in addition to quality and speed of service; this is our goal.

ENCAN® fall protection, a protecting brand.

Fall-protection harness with an incorporated mooring tail with 18 mm carabiner and fall shock absorber.
High tenacity and resistance polyester straps, with a maximum useful life.

High-quality forged steel lateral D-rings for positioning jobs. Their slight tilt simplifies the connection maneuver.

80 mm wide waistband strap for greater comfort when carrying out positioning jobs.
Shoulders, legs, and waist size is adjusted through steel adjusting buckles with keyholes for faster positioning. Fall indicator, which allows the user to detect if the harness fell and then proceed with its disposal.

Use: building, industries, and general tasks.

Data-sheet-harness-A40Download

Recommendations

Unwinding

The coil should be breaked while unwinding so that the wire rope comes out with a certain pressure and does not turn on its axis. This prevents bumps and kinks. If the coil is not equipped with brakes, then an operator should stop it..

Cables de Acero

Transport between coils

When the wire rope is carried from a full coil to an empty one or to a machine drum, this should be done from the upper or lower part of both, but never from the upper part of one coil and the lower part of the other, or vice versa.

Cables de Acero

Wire rope winding

The wire rope winding on the machine drum must be carried out correctly so that there are no spires overlapping and cross-linking, which would crush and distort the cords. The following figures represent the four cases that could effectively take place:

  1. Right torsional wire winding at the upper part of the drum.
    The mooring point should be located on the left side of the drum.
  2. Right torsional wire winding at the lower part of the drum.
    The mooring point should be located on the right side of the drum.
  3. Left torsional wire winding at the lower part of the drum.
    The mooring point should be located on the right side of the drum.
  4. Left torsional wire winding at the lower part of the drum.
    The mooring point should be located on the left side of the drum.

We do not recommend winding the wire around the drum in several layers, but if so, this technique is applied for the first layer of winding.

Cables de Acero

Deflection angle

The deflection angle is that formed by the wire from the first fixed pulley on the edge of the winding drum. It should not exceed 1º 30'.

Cables de Acero

Wire cutting

Cutting with shears or scissors. Before cutting, wires are to be tied together on both sides of the cutting area. The number of ties, the width and the distance between them depend on the wire diameter (see table). It is key to avoid longitudinal tilts among the different cord layers, since, in that case, those which have moved the least will bear the greatest part of the load, and there is the risk of breakage.

Cables de Acero
Tie characteristics
Wire rope diameterNo. of ties
on each side
of the cut		Tie
length		Distance
between ties		Wire diameter
rec. iron piece to be
used (mm)
Up to 12312150,5 to 0,8
13 to 20325401 to 1,5
21 to 30440501,2 to 2,2
31 to 40450501,8 to 3
41 to 50475502,2 to 3,2

Recommended cuttings

To cut antitwisting wire ropes, we recommend cutting by electric resistance or by welding.

Cables de Acero

Calibration

For calibration, the measuring device must be properly used.

Cables de Acero